The EBMX Talaria X3 PRO X9000 V3 Controller Plug N Play Kit is EBMX's controller upgrade built for the Talaria XXX PRO only, sold here at GritShift. Output runs from 6 kW to 50 kW depending on the build, with 1000 A of phase current, Wheel Lift Assist and a free mounting kit; 11.4 lb.
Specs verified October 2026 against the live GritShift product page and the EBMX tech sheet.
Specifications
| Bike | Talaria XXX PRO (X3 PRO only) |
|---|---|
| Power output | 6 kW up to 50 kW depending on build |
| Stock motor and battery | 7 kW can be run safely; EBMX recommends max settings of 110 battery amps, 400 A phase amps, 30% regen braking and 20% field weakening |
| Rated power | 50 kW, tested up to 60 kW |
| Phase current | 1000 A continuous, 1600 A burst (race mode) |
| Battery current | 500 A max line current |
| Input voltage range | 40 to 110V |
| Operating voltage range | 48 to 110V (26S) |
| Max efficiency | Over 95% |
| Motor control | Field Oriented Control (FOC); VESC based firmware, custom modified by EBMX per bike model |
| Operating temperature | -25 to 80 degrees C (-13 to 176 degrees F) |
| Waterproof rating | IP67 |
| IO count | 68 inputs and outputs |
| MOSFETs | 30 x 120V Infineon |
| PCB | Multilayer design with CNC copper busbars |
| Case | Full CNC alloy case |
| Cooling | Optional liquid cooling support |
| Power distribution | Billet CNC bus bar system |
| Power levels | 6 fully customizable, street and race toggle, regen tuning, speed limit and field weakening settings |
| Throttle | Dual hall throttle support (2 x ADC inputs) |
| Display | EggRider SW102 color display with custom firmware: live controller and motor temperatures, mode switching |
| Wheel Lift Assist | Integrated IMU, programmable launch, stunt and anti loop modes; throttle off angle default 50 degrees, start angle 10 to 15 degrees suggested, 30 degree minimum gap |
| Sensor protocols | CAN, RS485, UART, PWM in and out |
| App | Free iOS and Android EBMX X-Series app, Bluetooth connection, OTA firmware |
| Kit contents | Plug and play harness, X3 PRO mount kit, SW102T color display, 1-2 harness, Bluetooth module, thumb throttle, heat sink and hardware |
| Circuit protection | 200 to 250 A ANL fuse and/or circuit breaker required on every V3 install to maintain warranty coverage |
| Warranty | 2 years (stated on the product page) |
| Weight | 11.4 lb |
What bikes does the EBMX Talaria X3 PRO X9000 V3 kit fit?
- Talaria XXX PRO (X3 PRO only)
The standard Talaria XXX and X3 take the separate EBMX Talaria X3 X9000 V3 Controller Plug N Play Kit. Motor compatibility on the product page covers the OEM Talaria X3 and XXX motors, the EBMX XLB-60, the EBMX XUB-80, the QS138-70H, the QS138-90H and the other motors on its compatibility list.
What settings does EBMX recommend on a stock Talaria X3 PRO?
With the stock motor and battery the kit can safely run 7 kW. EBMX lists its recommended maximum settings for that setup on the product page: 110 battery amps, 400 A phase amps, 30 percent regen braking and 20 percent field weakening. Above that the build needs an aftermarket motor and battery to use the controller's 6 kW to 50 kW range, its 500 A battery line limit and its 1000 A continuous phase current with 1600 A bursts in race mode.
How does Wheel Lift Assist work on the X3 PRO kit?
Wheel Lift Assist is new for V3 and is not a wheelie mode: it only reduces throttle and applies regenerative braking from IMU data, never adding throttle on its own. The rider enables it in the EBMX app after accepting the waiver, then double taps the On button on the display. The throttle off angle defaults to 50 degrees for launching, EBMX suggests a 10 to 15 degree start angle on heavier bikes, and the two angles must sit at least 30 degrees apart. The auto horizon timer runs 0 to 30 seconds, braking force sets how much regen applies at the maximum angle, and a speed setting can switch the system off above a chosen speed. The full parameter list is in the EBMX Wheel Lift Assist sheet.
What is in the box with the X3 PRO X9000 V3 kit?
Shipping together are the plug and play harness, the free X3 PRO mounting kit, an SW102T color display and 1-2 harness, a Bluetooth module, the thumb throttle and a heat sink complete with hardware. Every V3 installation needs a 200 to 250 A ANL fuse and/or circuit breaker fitted per the installation guide on the QR code in the kit to keep the 2 year warranty. The display shows live controller and motor temperatures and switches modes, and the free iOS and Android app handles tuning and OTA updates. The EBMX X-9000 V3 sheet is linked from the product page.
Where can I buy the EBMX Talaria X3 PRO X9000 V3 Controller Plug N Play Kit?
Right here. We sell the EBMX Talaria X3 PRO X9000 V3 Controller Plug N Play Kit at GritShift, made by EBMX. Browse every EBMX part we carry in our EBMX collection.
