The EBMX E Ride Pro 2.0 X9000 V3 Controller W/Skid Plate & Mount Kit is a plug and play controller kit made by EBMX, sold here at GritShift, for the E Ride Pro-SS 2.0. The IP67 X9000 V3 runs 6 kW to 50 kW with FOC firmware and Wheel Lift Assist; 13.7 lb with breaker, 14 lb without.
Specs verified October 2026 against the live GritShift product page and the EBMX tech sheet.
Specifications
| Bike | E Ride Pro-SS 2.0 |
|---|---|
| Harness | V3 power harness (V3 plug type) |
| Mount | Skid plate and mount kit for the Pro-SS 2.0 |
| Power range | 6 kW to 50 kW |
| Stock motor limit | 14 kW with the OEM Pro-SS 2.0 motor |
| Stock battery limit | 14 kW with the stock, non bypassed Pro-SS 2.0 battery; more causes unsafe voltage sag |
| Options | With or without a circuit breaker |
| Rated power | 50 kW, tested to 60 kW |
| Phase current | 1000 A continuous, 1600 A burst in race mode |
| Battery current | 500 A max line current |
| Input voltage range | 40 to 110V |
| Operating voltage range | 48 to 110V (26S) |
| Max efficiency | Over 95% |
| Motor control | Field Oriented Control (FOC), VESC based firmware custom modified by EBMX per bike model |
| Operating temperature | -25 to 80 degrees C (-13 to 176 degrees F) |
| Waterproof rating | IP67 |
| IO count | 68 inputs and outputs |
| MOSFETs | 30 x 120V Infineon |
| PCB | Multilayer with CNC copper busbars |
| Case | Full CNC alloy |
| Cooling | Optional liquid cooling support |
| Power distribution | Billet CNC bus bar system |
| Ride modes | 6 fully customizable power levels, street and race toggle, regen tuning, speed limits, field weakening |
| Throttle | Dual hall throttle support, 2 x ADC inputs |
| Wheel Lift Assist | Integrated IMU with programmable launch, stunt and anti loop modes |
| Sensor protocols | CAN, RS485, UART, PWM in and out |
| Kit contents | Plug and play harness, mount kit for the bike, SW102T color display, 1-2 harness, Bluetooth module, thumb throttle, heat sink and hardware |
| Circuit protection | 200 to 250 A ANL fuse and/or circuit breaker required to keep warranty coverage |
| Warranty | 2 years (stated on the product page) |
| Weight | 13.7 lb with breaker, 14 lb without breaker |
What bikes does the EBMX E Ride Pro 2.0 X9000 V3 kit fit?
- E Ride Pro-SS 2.0
Motor compatibility on the product page covers the OEM E Ride Pro-S and Pro-SS motors, the EBMX XLB-60 and EBMX XUB-80, the QS138-70H, the QS138-90H and QS165 motors, and the other motors on its compatibility list. Two motors are listed as not yet compatible while EBMX tests app support for them.
How much power can the X9000 V3 put through a stock Pro-SS 2.0?
The controller itself spans 6 kW to 50 kW, rated at 50 kW and tested to 60 kW, with 1000 A of continuous phase current and 1600 A bursts in race mode. On a stock bike the limits sit elsewhere: EBMX says an OEM E Ride Pro-SS 2.0 motor can safely run 14 kW, and a stock, non bypassed Pro-SS 2.0 battery can also safely run 14 kW, with anything higher producing unsafe voltage sag.
What does Wheel Lift Assist do on the X9000 V3?
Wheel Lift Assist (WLA) uses the controller's integrated IMU to modulate throttle and apply regenerative braking when the front end lifts, within angles the rider sets; it never adds throttle on its own. The throttle off angle defaults to 50 degrees for launching, the suggested start angle for heavier bikes is 10 to 15 degrees, and EBMX requires at least a 30 degree gap between the two. Auto horizon calibration runs on a 0 to 30 second timer, and a speed setting can switch WLA off above a chosen speed. Full settings are in the EBMX Wheel Lift Assist sheet linked from the product page.
What ships in the E Ride Pro 2.0 X9000 V3 kit?
The kit arrives with the plug and play V3 power harness, the skid plate and mount kit for the Pro-SS 2.0, the SW102T color display, a 1-2 harness, the Bluetooth module, a regen thumb throttle, and the heat sink with all hardware, with or without a circuit breaker depending on the option chosen. Every V3 installation still needs a 200 to 250 A ANL fuse and/or breaker fitted per the installation guide reached through the QR code in the kit, or warranty coverage lapses. The EBMX X-9000 V3 sheet and the free EBMX app (iOS and Android) cover live tuning, OTA firmware updates and diagnostics.
Where can I buy the EBMX E Ride Pro 2.0 X9000 V3 Controller W/Skid Plate & Mount Kit?
Right here. We sell the EBMX E Ride Pro 2.0 X9000 V3 Controller W/Skid Plate & Mount Kit (V3 Power Harness) at GritShift, made by EBMX. Browse every EBMX part we carry in our EBMX collection.
