The EBMX E Ride Pro SR X9000 V3 Controller & Mount Kit is a complete plug and play controller upgrade made by EBMX, sold here at GritShift, for the E Ride Pro-SR. It delivers 6 kW to 50 kW on stock or 96V big motor builds, includes a custom CNC mount and the EggRider SW102 display, and weighs 12 lb.
Specs verified October 2026 against the live GritShift product page and the EBMX tech sheet.
Specifications
| Bike | E Ride Pro-SR |
|---|---|
| Power range | 6 kW to 50 kW, fully tunable |
| Rated power | 50 kW, tested to 60 kW (EBMX sheet) |
| Voltage | 120V (EBMX sheet) |
| Phase current | 1000 A, 1600 A burst (EBMX sheet) |
| Builds | Stock motor and battery, or full 96V big motor builds |
| Mount | Custom CNC machined mount for the Pro-SR |
| Display | EggRider SW102 color display with real time temperatures and live ride adjustments |
| Motor control | Custom EBMX VESC firmware with Field Oriented Control |
| Motor tunes | 30 plus preloaded |
| Wheel Lift Assist | Anti loop control of front end lift during acceleration, launches and climbs; not a wheelie mode |
| MOSFETs | Infineon (EBMX sheet) |
| Construction | Full CNC case, interchangeable heat sinks, billet CNC bus bar system (EBMX sheet) |
| Operating temperature | -25 to 80 degrees C (EBMX sheet) |
| IO count | 68 (EBMX sheet) |
| Kit contents | All hardware and wiring, CNC mount, EggRider SW102 display; the sheet lists the plug and play harness and mount kit, SW102T display, 1-2 harness, Bluetooth module, thumb throttle, heat sink and hardware |
| Circuit protection | 200 to 250 A ANL fuse and/or circuit breaker required to keep warranty coverage |
| Warranty | 2 years (stated on the product page) |
| Weight | 12 lb |
What bikes does the EBMX E Ride Pro SR X9000 V3 kit fit?
- E Ride Pro-SR
The motor compatibility list on the product page names the OEM E Ride Pro-SR motor, the EBMX XLB-60, the EBMX XUB-80, the QS138-70H and QS138-90H, and other motors listed there.
What makes the Pro-SR X9000 V3 kit a complete upgrade?
EBMX built this kit specifically for the E Ride Pro-SR, so it arrives with all hardware, the wiring, a custom CNC machined mount and the EggRider SW102 color display, and installs plug and play. It runs the stock Pro-SR motor and battery as happily as a full 96V big motor build, with 6 kW to 50 kW of fully tunable output; the EBMX sheet rates the controller at 50 kW, tested to 60 kW, with 1000 A of phase current and 1600 A bursts. The 2 year warranty depends on fitting a 200 to 250 A ANL fuse and/or circuit breaker as the installation guide directs.
How does the SW102 display and FOC firmware change the ride?
EBMX's custom VESC firmware with Field Oriented Control is tuned for a throttle that is smooth yet razor sharp, and 30 plus preloaded motor tunes make the initial setup quick. The EggRider SW102 display provides real time temperatures and live ride adjustments, while the X-Series app on the EBMX X-9000 V3 sheet adds setup in minutes, live tuning at the track and OTA updates. Wheel Lift Assist watches front end lift during acceleration, launches and climbs; EBMX is explicit that it is an anti loop feature, not a wheelie mode.
Can the Pro-SR kit run a bigger motor later?
Yes. The same controller carries a Pro-SR from its stock motor to a 96V big motor build, and the compatibility list already includes the XLB-60 and XUB-80 motors we carry alongside the QS138 family. The sheet adds Load and Go battery profiles with over 15 plug and play setups and tunes for 30 plus motors. For the IMU settings behind Wheel Lift Assist, the EBMX Wheel Lift Assist sheet is linked from the product page.
Where can I buy the EBMX E Ride Pro SR X9000 V3 Controller & Mount Kit?
Right here. We sell the EBMX E Ride Pro SR X9000 V3 Controller & Mount Kit at GritShift, made by EBMX. Browse every EBMX part we carry in our EBMX collection.
